Belkin Conserve Valet Betriebsanweisung PDF herunterladen (Seite 6)

Check all the cables on the Conserve Valet

and make sure they are connected securely.

Each port on the Conserve Valet is rated to

supply 500mA. However, some new devices

require more current than 500mA. Devices

with large color screens, such as smart

phones, often require more than 500mA.

The Conserve Valet has been designed with

additional charging capacity to accommodate

the majority of these types of devices. If your

connected device still does not begin to

charge, it is possible that the Conserve Valet

has reached its maximum charging capacity.

Try removing each attached device one by

one, pressing the start button after each

device is disconnected until the Conserve

Valet turns on (LED will illuminate green). It is

recommended you only charge two devices

with large color screens at the same time.

I disconnected all my devices, but the

Conserve Valet stays on.

The Conserve Valet will detect when all

devices have been removed and will power

down automatically after approximately

two minutes.

NOTE: This product’s USB outlets cannot be

used as USB hubs and do not transmit data.

The powered USB outlets on this unit are

intended solely for charging devices that can

be charged via USB interface.

Speciﬁcations

Power Input: 100–240V~, 50/60Hz 0.5A

Power Output: +5V/500mA x 4 USB 2.0 port

Safety Information

Important: Use indoors in a dry location.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

Belkin International, Inc., is not responsible for any interference

caused by unauthorized modiﬁcations to this equipment. Such

modiﬁcations could void the user’s authority to operate this

equipment.

Limited One (1) Year Warranty

What this warranty covers.

Belkin International, Inc., warrants to the original purchaser of

this Belkin Conserve Valet, that the Conserve Valet shall be free of

defects in design, assembly, material, or workmanship.

What the period of coverage is.

Belkin International, Inc., warrants the Belkin Conserve Valet for

one (1) year from the original date of purchase.

TROUBLESHOOTING

My device does not charge when

connected to the Conserve Valet.

Check that your Conserve Valet is securely

plugged into a power outlet. Next you’ll want

to make sure that any device attached to

your Conserve Valet is securely connected

at both ends. Ensure that the start button

has been depressed and that the Conserve

Valet’s LED is green. If your device does not

begin to charge, disconnect the Conserve

Valet and your device and reconnect them as

described in the Quick Setup Guide.

NOTE: The Conserve Valet has been

designed with in-line signal resistors to work

with as many devices as possible. However,

the Conserve Valet’s conﬁguration might not

be compatible with your device if it does

not charge when securely connected to the

Conserve Valet. Check with a local or online

retailer, or with your device manufacturer for

a compatible USB data connector cord that

has built-in signal resistors to enable the

charging of your device.

After connecting devices to the Conserve

Valet and during operation, the LED light

goes out and my electronics appear not to

be charging. Additionally, when I plug in

my powered-down devices and press the

start button, the LED turns on, and then

turns off and stays off.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Belkin Conserve Valet Betriebsanweisung Seite 6

Kommentare zu diesen Handbüchern