Belkin F5U251 - SATA II RAID PCI Express Card Controller Installationsanleitung PDF herunterladen

Technical Support Information

F5U197/F5U251 SATA II RAID 2-Port PCI Express Card Installation Guide

Below is a step by step guide for installing the F5U197/251, and then verifying the card is installed correctly

using the supplied drivers allowing it to function correctly.

Initial Installation

1. Unpack the card and the installation disk, DO NOT install the card into your pc at this time.

2. Insert the installation CD, a Belkin menu should automatically appear. If it does not then click “Start | Run” and

type “X:\autorun.exe” (With X being the drive letter of your CD drive).

3. Click “Install Driver”, the setup for the SATA driver and RAID software should run and install the drivers onto

your pc, if requested reboot the computer.

4. Close the menu and shut down your computer.

5. Insert the F5U197/251 into an empty PCI Express slot and secure using the bracket or screws provided in your

pc case. Close the case and turn the computer back on.

6. Windows will install a number of hardware items automatically, allow it to do this and once completed you can

proceed to verifying the installation.

Verifying the Installation – SATA Controller

1. Open your Windows device manager (Right click on My Computer and select “Properties”, then click on the

“Hardware” tab and click on the button that says “Device Manager”), expand the section “SCSI and RAID

controllers” and you should see the following.

2. As stated in the manual once you have verified that the device above is installed then your card is installed

correctly.

Belkin Ltd Express Business Park Shipton Way Rushden England NN10 6GL | eurosupport@belkin.com | www.belkin.com

Page 1

1 2 3 4 5 6

Technical Support Information 1

Inhaltsverzeichnis

Seite 1 - Technical Support Information

Technical Support InformationF5U197/F5U251 SATA II RAID 2-Port PCI Express Card Installation GuideBelow is a step by step guide for installing the F5U

Seite 2

Technical Support InformationSetting up Your SATA Drive(s)Now that your card is installed your can switch the computer off and connect up your SATA ha

Seite 3

Technical Support Information3. To use the drive as a stand alone disc you need to create a Legacy RAID group as shown above, for instructions on sett

Seite 4

Technical Support InformationChecking and Initialising the drive in the Windows OSYour drive(s) should now be ready to use, but before you can access

Seite 5

Technical Support Information3. Click “Next” to proceed.4. Make sure the tickbox next to “Disk 1” is selected to be initlialised and click “Next”.5. A

Seite 6

Technical Support Information7. You will now return to the Disk Management screen, you will notice that Disk1 now shows as online. If the partition on

Weitere Dokumente für Vernetzung Belkin F5U251 - SATA II RAID PCI Express Card Controller

Um das Dokument anzuzeigen Belkin F5U251 - SATA II RAID PCI Express Card Controller Bedienungsanleitung

Belkin F5U251 - SATA II RAID PCI Express Card Controller Bedienungsanleitung (84 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Belkin F5U251 - SATA II RAID PCI Express Card Controller Installationsanleitung

Stöbern Sie online oder laden Sie Installationsanleitung nach Vernetzung Belkin F5U251 - SATA II RAID PCI Express Card Controller herunter. Belkin F5U251 - SATA II RAID PCI Express Card Controller Installation guide Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Vernetzung Belkin F5U251 - SATA II RAID PCI Express Card Controller

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Belkin F5U251 - SATA II RAID PCI Express Card Controller