Belkin ePowerSwitch Bedienungsanleitung

User Manual ePowerSwitch By: BELKIN 34000179 19-Sep-02 Copyright© 2000

6 6 IP Setup This section describes the IP set up & configuration of the ePowerSwitch System when you connect i

7 The following steps guide you in connecting the ePowerSwitch System through the Ethernet port 1. Connect the Ethernet port to the network with

8 8 2. Setup via serial port Before setup you need: 1. IP address: Get a valid IP address from administrator.

9 The following steps guide you in connecting the ePowerSwitch System through the serial port 1. Connect the RS232 port to a dumb terminal/PC w

10 10 3. Press OK if you have the Windows Communications screen or accept your communication settings in the terminal

11 Note: The telnet setup procedure is the same as the serial setup. When the configuration is completed, remember to save and restart. Seria

12 12 Figure 4 - IP Address for the ePowerSwitch System and More NOTE: The minimum requirement to operate ePowerSwi

13 To Save and Exit If you are satisfied with your configurations, be sure to save them and exit. 3. Setup via USB port Before setup you nee

14 14 to see the device because the ePowerSwitch takes about 30 seconds to boot. 2. The “USB-interface power device”

15 3. USB setup is straightforward once the PC has successfully detected USB device. See the following figure. You need to run Device | Updat

Trademarks IBM, IBM NetView/6000 are trademarks or registered trademarks of International Business Machines Corp. Hewlett-Packard, HP, HP Open View ar

16 16 adapter you may access the configuration menu as if you were directly attached to it via the configuration port.

17 Configuration PPP Configuration PPP connection is useful if it is not possible to make a direct network connection to the ePowerSwitch. Aga

18 18 Remote operation procedure 1. The remote user may hang up after three rings when dial in. 2. Based on the conte

19 User Management Administrators can assign the maximum of 4 users to control the outlet.

20 20 Software Update This is the place you can upgrade the firmware when it is available or bug fix.

21 ePowerSwitch Configuration Each outlet can be individually programmed to enable ring On/Off or reset. Power resume delay is convenient for

22 22 To enable this safe shutdown function, in both NT and WIN 2000, you need to have three setting for the UPS to con

23 Scheduled shutdown Scheduled shutdown can be accomplished here. Be careful with which outlet you are working.

24 24 Verify The ePowerSwitch Operation 1. After you complete all configuration settings and connect the ePowerSwitch

25 Upgrade Firmware TFTP Upgrade With a Web browser, click on “Software upgrade”, input TFTP server’s IP address and go. Make sure that the f

Table of Contents i Table of Contents Introduction...1 ePowerSwitch F

26 26 the user data are lost.

27 Telephone Interface You must have the optional phone card installed inside the ePowerSwitch Server for all the functions discussed here. P

28 28 ePowerSwitch ID Address ePowerSwitch Outlet Function XX X X 01-16 1-8 ? A-H 0-Off 9 ? All 1-On 2-R

29 9. User enter 888XXX…..# or whatever previous password, then ePowerSwitch responds with three short beeps acknowledge access granted. Then

30 30 Appendix This appendix has three sections: Reference, Glossary, and Troubleshooting. Reference This section di

31 IP addresses appear in dotted decimal (rather than in binary) notation. Dotted decimal notation divides the 32-bit value into four 8-bit grou

32 32 segments the network address into 100 subnetwork addresses. (If the Class B network address is 150.1.x.x, the add

33 first three octets. Gateways Gateway, also referred to as a router, is any computer with two or more network adapters connecting to differen

34 34 Glossary The Glossary section defines the terms used in the ePowerSwitch System -MP environment. Agent Implemente

35 NO Normally Open—Refers to a contact switch that is normally open. OID Object Identifier—The variables defined in a MIB. Personality The c

ii ii Telephone access interface ...27 Appendix...

36 36 Troubleshooting Problem: The TES (Terminal Emulation Software) does not display anything. Solution: Make sure

1 Introduction The ePowerSwitch is a network-manageable, intelligent power control unit designed to provide control of power for up to eight el

2 2 ?? Works with all major NMSs on Ethernet— ePowerSwitch System works with the most widely used Network Management Sy

3 On/Off Buttons – control for each of the corresponding rear socket. Press and hold for 3 seconds to setup up the Remote/local control for eac

4 4 ePowerSwitch System Package The standard ePowerSwitch System package contains an ePowerSwitch System Unit with su

5 for 10Base-T networks. Once connected, it is possible to use the ARP command to set IP address through the network interface. USB Connector