Keyboard
Q: The Keyboard is not detected, or a keyboard error is received during boot-up. o Check cable connections
* Make sure the keyboard works when it is connected directly to the computer s Make sure you are using the correct power supply, it
should be 9VDC 600 mA. Try a different keyboard
* When cascadingtoanFID066,are A31648-06keyboardcable.
You should hear a beep to confirm the OmniView' has switched to the desired port. For example, pressing <ALT>+<CrRL>+<SHIFT> 1 2 3
<ENTER> selects Port I on the top level OmniView, Port 2 on the second level OmniView', and Port 3 on the third level OmniView.
The OmniView" filters out the hot-key sequences, preventing unwanted characters from appearing in the computer's applications.
Scan Mode
The OmniView can be sent for automatic scan mode. hi scan mode, the OmniView" switches from one computer to the
next in 10-second intervals. When the OmniView is in scan mode, there is no keyboard control passed to the displayed
computer. This is necessary because switching is handled by the OmniView", not the operator.
Note: Scan Mode will continue indefinitely, until the <SPACE> bar is pressed and scan mode is terminated. Also, the
OmniView' will only scan to ports that have computers enabled on it.
*
To invoke scan mode, the following hot-key sequence must be entered:
<ALT>+<CT'RL>+<SHIFT> 0 <ENTER>
You will then hear a beep to confirm scan mode is taking place, and this can be verified visually by the flashing
lights on the currently selected computer port.
Quick Last/Next switching mode
Quick Last/Next switching mode is similar to scan mode, except the operator has control over the switching. In this mode,
the operator can press either one of the shift keys to switch to the adjacent computer previous or after the currently
selected port. There is also no keyboard control during this mode, but the mouse is still completely operable.
Note: Quick Last/Next switching mode will continue indefinitely, until the <SPACE> bar is pressed and is terminated.
*
To invoke quick Last/Next switching mode, the following hot-key sequence must be entered:
<ALT>+<CTRL>+<SHIFT'> 9 <ENTER>
You will then hear a beep to confirm quick Last/Next switching mode is taking place, and this can be verified visually by the slow blinking
light on the currently selected computer port.
To select the next adjacent computer, press the RIGHT side <SHIFT> key.
To select the previous adjacent computer, press the LEFT side <SHIFT> key.
WARNING!
Make sure that all equipment is turned off when connecting or disconnecting any cables. Plugging and unplugging
cables while the computer or OmniView
are powered could potentially damage the computer, the OmniView
,
or both.
Video
Q: What are the technical specs for the video section of the OmniView""?
* Compatible with VGA, SVGA and Multisync monitors
* Monitor Support: RGB Analog, Horizontal Sync, Vertical Sync
* VGA Bandwidth: 180 MHz
* VGA Resolution max: 1280 x 1024
Q: The monitor is fuzzy or I am getting ghosting or shadowing. What do I do?
* Check cable connections
* If shadowing only happens from one computer, try swapping the cables
* If possible, try a lower video resolution and/or refresh rate
* For high resolutions and/or long distances use A3H981-XX-T cable, where'-XX " denotes the length of the cable in feet.
Q. I have a Monochrome monitor and it is not working. Why not?
* The OmniView"" supports SVGA, VGA, and Multisync monitors only
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern