Belkin XM Commander Spezifikationen Seite 110
- Seite / 164
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
REF: BB_SRM_xM BeagleBoard-xM System
Reference Manual
Revision A2
Page 110 of 164
additional delay may be needed to be added before the circuitry is activated. Refer to the
processor and TPS65950 documentation for more information.
8.25 LCD Expansion Header
If you choose not to use the LCD headers for access to the LCD signals or for the DVI-D
interface, they can also be used for other functions on the board based on the pin mux
setting of each pin. Table 24 shows the options for P11 and Table 25 shows the options
for P135. The MUX: column indicates which MUX mode must be set for each pin to
make the respective signals accessible on the pins of the processor.
Table 24. P11 GPIO Signals
Pin# Signal
MUX:0 MUX:2 MUX:4
3 DVI_DATA1 DATA1 UART1_RTS GPIO71
4 DVI_DATA0 DATA0 UART1_CTS GPIO70
5 DVI_DATA3 DATA3 - GPIO73
6 DVI_DATA2 DATA2 - GPIO72
7 DVI_DATA5 DATA5 UART3_TX GPIO75
8 DVI_DATA4 DATA4 UART3_RX GPIO74
9 DVI_DATA12 DATA12 GPIO82
10 DVI_DATA10 DATA10 - GPIO79
11 DVI_DATA23 DATA23 - GPIO93
12 DVI_DATA14 DATA14 - GPIO84
13 DVI_DATA19 DATA19 McSPI3_SIMO GPIO89
14 DVI_DATA22 DATA22 McSPI3_CS1 GPIO92
15 I2C3_SDA I2C3_SDA - -
16 DVI_DATA11 DATA11 - GPIO81
17 DVI_VSYNC VSYNC - GPIO68
18 DVI_PUP DVI_PUP - -
Table 25. P13 GPIO Signals
Pin# Signal
MUX:0 MUX:2 MUX:4
3 DVI_DATA20 DATA20 McSPI3_SOMI GPIO90
4 DVI_DATA21 DATA21 McSPI3_CS0 GPIO91
5 DVI_DATA17 DATA17 - GPIO87
6 DVI_DATA18 DATA18 McSPI3_CLK GPIO88
7 DVI_DATA15 DATA15 - GPIO85
8 DVI_DATA16 DATA16 - GPIO86
9 DVI_DATA7 DATA7 UART1_RX GPIO77
10 DVI_DATA13 DATA13 - GPIO83
11 DVI_DATA8 DATA8 - GPIO78
12 NC - - -
13 DVI_DATA9 DATA9 - GPIO79
14 I2C3_SCL I2C3_SCL -
15 DVI_DATA6 DATA6 UART1_TX GPIO_76
16 DVI_CLK+ PCLK - GPIO66
17 DVI_DEN DEN - GPIO69
18 DVI_HSYNC HSYNC - GPIO67
- BeagleBoard-xM Rev A2 1
- System Reference Manual 1
- Table of Contents 5
- Figures 9
- Tables 11
- 1.0 Introduction 13
- 2.0 Change History 15
- 2.2.2 Software Changes 16
- 4.0 BeagleBoard Overview 17
- Figure 2. USB Y-Cable 21
- 6.0 Product Contents 28
- 7.0 BeagleBoard Hookup 30
- BEAGLEBOARD 36
- VOLT_ERR 45
- 8.2.1 Detection 46
- 8.2.2 Indication 46
- 8.2.3 Shutdown 46
- USB_CLIENT / 47
- OTG PORT 47
- DC_POWER 47
- 8.3.1 USB DC Source 48
- 8.3.2 Wall Supply Source 48
- 8.3.3 DC Source Control 48
- 8.3.4 AUX 3.3V Supply 49
- Figure 25. Main Power Rails 55
- 8.7.6 VOCORE_1V3 56
- 8.7.7 VDD2 56
- 8.8.1 VDD_PLL2 57
- 8.8.2 VDD_PLL1 58
- 8.8.3 VDAC_1V8 58
- 8.8.10 EXP_VDD 60
- 8.9.1 Boot Configuration 60
- 8.9.2 RTC Backup Battery 60
- 8.9.3 Power Sequencing 61
- Figure 27. Power Sequencing 61
- 8.9.4.3 User Reset 63
- 8.9.4.4 PWRON 63
- 8.9.5 mSecure Signal 63
- 8.10.1 Overview 64
- 8.10.2 SDRAM Bus 65
- 8.10.3 GPMC Bus 65
- Processor 66
- 8.10.9 GPIO Mapping 69
- 8.10.10 Interrupt Mapping 69
- Figure 33. POP Memory 70
- Figure 34. System Clocks 70
- 8.12.1 32KHz Clock 71
- 8.12.2 26MHz Clock 71
- 8.12.2.1 26MHz Source 71
- 8.12.2.2 TPS65950 Setup 71
- 8.12.2.3 Processor 26MHz 71
- 8.12.3 McBSP_CLKS 72
- 8.13.1 USB OTG Overview 72
- 8.13.2 USB OTG Design 73
- Figure 35. USB OTG Design 73
- 8.13.3 OTG ULPI Interface 73
- 8.13.3.2 TPS65950 Interface 74
- 8.13.4 OTG Charge Pump 74
- 8.13.5 OTG USB Connector 75
- 8.13.6 OTG USB Protection 75
- 8.14.1 Power 76
- 8.14.2 HS USB PHY 77
- Figure 38. USB PHY Design 78
- 8.14.3 USB HUB 79
- Figure 39. USB HUB Design 80
- 8.14.4 USB Port Connectors 81
- 8.14.5 Ethernet 82
- 8.15.1 microSD Power 83
- 8.15.2 Processor Interface 83
- 8.15.3 Card Detect 84
- Figure 43. Audio Circuitry 85
- 8.16.3 Audio Output Jack 86
- 8.16.4 Audio Input Jack 86
- Figure 44. DVI-D Interface 87
- 8.17.2 LCD Power 89
- 8.17.3 TFP410 Power 89
- 8.17.4 TFP410 Framer 89
- 8.17.6.8 DVI to VGA 93
- Table 16. P11 LCD Signals 93
- Table 17. P13 LCD Signals 94
- 8.20.4 Camera Modules 100
- Figure 47. Camera Modules 100
- 8.21.1 Processor Interface 101
- 8.21.2 Level Translator 101
- 8.21.3 RS232 Transceiver 102
- 8.21.4 Connector 102
- 8.22.1 Power Indicator 103
- 8.22.2 PMU Status Indicator 103
- Figure 49. Indicator Design 103
- 8.22.3 User Indicators 104
- 8.22.4 HUB Power Indicator 104
- Figure 50. JTAG Interface 105
- 8.23.1 Processor Interface 105
- Table 21. JTAG Signals 105
- 8.23.2 JTAG Connector 106
- 8.24.1 Processor Interface 106
- 8.24.2 Expansion Signals 108
- 8.24.3 Power 109
- 8.24.4 Reset 109
- 8.24.5 Power Control 109
- Table 24. P11 GPIO Signals 110
- MUX:0 MUX:2 MUX:4 110
- Table 25. P13 GPIO Signals 110
- 8.26.1 MCBSP5 Signals 111
- 8.26.2 MMC3 Signals 112
- 8.26.3 ETK Signals 112
- 8.26.4 HSUSB1 Signals 113
- 8.26.5 Alternate Clock 113
- 8.26.6 HDQ 1-Wire 113
- 8.26.7 ADC 113
- 8.26.8 GPIO Signals 114
- 8.26.9 DMAREQ 114
- Figure 52. Power Connector 115
- Figure 56. DVI-D Connector 118
- DVI-D interface itself 118
- Figure 57. DVI-D Cable 119
- Figure 58. DVI-D Cable 119
- 9.5.1 Connector Pinout 120
- Table 33. P11 LCD Signals 120
- Table 34. P13 LCD Signals 121
- 9.5.2 Camera 122
- Figure 60. Camera Connector 123
- Figure 61. Camera Module 123
- 9.5.3 Audio McBSP2 Port 124
- 9.5.6 Mounting Scenarios 127
- Figure 66. Audio In Plug 128
- Figure 68. Audio Out Plug 129
- Table 39. JTAG Signals 130
- 9.9.1 Battery 132
- Figure 73. Optional Battery 132
- 9.9.2 Battery Installation 132
- Figure 75. Resistor R65 133
- Table 41. DC Power Supplies 135
- Figure 76. DC Power Supply 135
- Figure 79. USB to Bluetooth 138
- 11.0 Mechanical Information 140
- 11.2.1 Mounting Method 141
- 11.2.2 Expansion EEPROM 143
- Table 46. Voltages 145
- 12.1.1 Signal Access Points 146
- Table 47. Troubleshooting 147
- 13.0 Known Issues 148
- 15.0 Schematics 151
- 16.0 Bills of Material 163
- 17.0 PCB Information 164
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.206 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern